Welcome Stranger to OCC!Login | Register

NZXT Beta Review

Geekspeak411    -   August 4, 2009
» Discuss this article (1)

Lowest Prices

Closer Look:

Upon opening the Beta, which was very easy thanks to the thoughtful inclusion of tool-less side panel screws, I instantly admired the sleek black paint job applied to the interior. All of the PCI covers are perforated allowing for extra airflow. There is also a large vent next to the slots, which will allow for hot air coming out of a video card's cooler such as the GTX 295's, to exhaust out of the case rather than stay trapped inside. There is a 120mm opening in the usual spot on the back, but surprisingly a fan is not included - undoubtedly left out to cut costs. I'm not sure whether this was a wise move however, because I have trouble believing a case with one fan will be able to keep an overclocked gaming rig cool. Without proper ventilation, a system can become very unstable and even crash during peak temperatures ie: during gaming. I suppose we will just have to wait and see how the Beta performs in the testing regiment.

There is a little white cardboard box in the bottom right corner of the case which includes all of the Beta's accessories. The the top mounted I/O panel's cables are joined with the front panel's cables neatly wrapped and twist-tied together. There is also a cord for the front 120mm fan which interestingly enough has both a 3-pin motherboard adapter, and a 4 pin Molex adapter. At this point I am not sure if they can both run the fan independent of each other, or if the motherboard connector is just to adjust the speed of the fan while being powered straight from the PSU through the Molex. You can also see the holes drilled and set back for cable management.

 

 

 

 

 

 

 

Like I said above, the little white box inside of the case contains all of the accessories that NZXT thinks you will need with the Beta. Those accessories are: 4 Tool-Less Floppy Disk Mounts (uses two per drive), 8 Tool-Less 5.25" Drive Mounts (uses two per drive), not one but two bags of varied screws, headers, and spacers, a little screw-on adapter allowing you to lock your side door, a motherboard speaker, and 10 Tool-Less 3.5" Hard Drive Mounts (uses two per drive.) There is also a little sheet of paper thanking the purchaser for buying a NZXT product in four different languages, and states that the manual can be found online here under their downloads section. I included one of the 5.25" drive bay covers in the picture too below the white box.

 

 

The fan itself is a standard grade NZXT with blue LED's. Knowing most case fans are junk, I wouldn't expect too much from this but only testing will tell!

 

Installing components into the Beta was a painless activity. The thumbscrews on the side panel were a nice addition, and all of the tool-less components worked as they should, which made the whole experience hassle free. I do have a couple of complaints however. If you are going to put good tool-less mounts for the 5.25" bays, the 3.5" bays, and include thumbscrews for the side panel, why in the world would you put some plain-jane screws in to secure the PCI cards? Now If it's because they didn't trust the plastic tool-free mounts that are out there for PCI cards then I don't blame them. But why not put thumbscrews in? When I install the OCC test bench into a system I usually only expect to have to use a screwdriver in the motherboard screws, which if anyone can come up with a good tool-less idea for motherboard installation, I would support them forever. But I was surprised when I saw that I had to crunch my fingers into the back panel to get the right angle with my screwdriver on the PCI screws rather that just twist them out with my fingers.

With the 5.25" drive bay mounts really all you have to do is slide your drive in, line up the 2 pins on the mount with the screw holes on the drive, push and twist the knob on the mount 90 degrees. It really is that simple! It is also secure - I think that my drive would stay in the case just fine with only one mount attached.

 

 

Once everything is installed, I found that there really is no place for the extra cables to go. I never thought about it before but NZXT engineers designed the Beta so that the motherboard tray goes all the way from the bottom of the case to the top. No hole for extra cables to be seen. Now with NZXT aiming at gamers here I don't know how in the world they though they would get by without! Almost every custom builder posts pictures of their rig at some point, whether to show off or to get some help with trouble shooting. Either way builders like you and I know that to get the most out of your system, you have to tuck those extra cables away so that they don't obstruct airflow and so that you can see and show off the guts of your rig. NZXT did put cable management holes underneath the motherboard but there is no way to string your cables to them without wrapping them around the drive bay, which would take about 3 feet or more of cable. This is something I for one, don't have. Instead, I had to stuff all of my extra cables into the two empty 5.25" drive bays which completely blocked the possible air flow opportunities, defeating the purpose of the wonderful drive bay covers that I like so much.

 

With this review, the Beta was put through some additional testing which I wasn't going to include, but after the results I feel that I would be doing you, the reader and possible consumer, a huge disservice by omitting the facts. I moved halfway through the review which means that my systems had to come with me. Like anyone going to a LAN party etc. would, I got my rig ready to ship. I took out the graphics card, I took out the hard drive and unlike most I took an extra precaution by packing the interior to the brim with packing peanuts. I had tightened down all of the screws and made sure everything was good to go. I put the case into it's original shipping box and sent it off. When it got here however, I was appalled. In order to keep the Beta lightweight, and to cut down costs I would imagine, NZXT used thin steel to construct the case. Now when I was installing the OCC test bench I noticed how the back panel flexed a good bit when I pressed the lip right above the PCI slot openings, but I didn't think much of it. Now I see that I should have. When I opened up the Beta to empty out the packing peanuts and reinstall the graphics card and the hard drive I found that the back of my PSU, a Cooler Master RPP 850w had sunken down far below where it should have been. This wouldn't have been that big of a problem except for the fact that since I had the PSU's cords under the PSU unit for lack of cable management, and I had a few packing peanuts up there to fill in the gaps, the PSU had actually made contact with the CPU cooler, a Cooler Master V8, via the extra cords and bent the cooler so that it about a half-inch lower than where it should have been. Luckily the motherboard didn't crack, although the motherboard tray was bent out of shape around the upper stand-offs.

Now how did all of this actually happen? Well it was actually a combination of things. The part of the case that the PSU mounts onto wasn't sturdy enough to hold the unit in place and had bent all out of shape around the screws which you can see in the first picture, the plate holding the PSU was flush to the upper panel you see in the picture when I got the case. In the second picture you can see one of the bottom screw holes which wasn't bent out of shape, originally the top one was a smooth at the bottom.

 

 

Now to keep this from happening, manufacturers have put either a metal tab extending out from the motherboard tray or a bar that the PSU sits on. Occasionally you will see both. In this case, NZXT went with a tab extending from the motherboard tray. Like the PSU mount however, the steel was too thin and wasn't curved to add support. When the mount bent, so did the tab. In the picture below, you can see what happened. I would recommend opening the larger version if you are interested because even after moving the cords and everything, it was difficult to get the light and the camera in the right place so that you could even see the tab, so please excuse the poor picture quality.

 

To give you an overall look at the damage, I have included a picture of the side of the unit. I was able to fix the problem to an extent after which I took the picture that has everything installed, seen above. When comparing the two pictures, notice just how far the PSU has sagged and note that the Cooler Master V8 was originally level with the 120mm vent in the back, even after adjusting the brightness and contrast ratios, I was unable to get the motherboard to show up.

 

I'll have to keep the PSU issue in the back of my mind until the conclusion. For now, let's see what I found on NZXT's website!




  1. Introduction & Closer Look
  2. Closer Look (The Case)
  3. Closer Look (Working Components)
  4. Specifications & Features
  5. Testing: Setup & Results
  6. Conclusion
Random Pic
© 2001-2014 Overclockers Club ® Privacy Policy

Also part of our network: TalkAndroid, Android Forum, iPhone Informer, Neoseeker, and Used Audio Classifieds

Elapsed: 0.1297399998